Advanced Industrial v1.1.0 (deprecated)
Scope
Provide support for SDI-12, 4-20mA and pulse input sensors with flexible configurations. It is applicable to Agriculture & Environmental Monitoring applications.
General Information
| Host board | insigh.io main board |
| Version | v1.1.0 |
| Supported Digital Interfaces | 2 x SDI-12 & 2 x 4-20mA & 1 x Pulse Counter |
| Sensor Headers | Fixed Terminal Block with push-in connection (no tools required) |
| 1x8-pin (SDI-12 & Pulse Counter) & 1x6-pin (4-20mA) | |
| Dimensions (L x W x H) | 41.3 x 47 x 16.7 mm |
| Weight | 16 g |
Example Applications
- Precision Agriculture
- Soil moisture, Electrical Conductivity, Volumetric Water Content, Temperature
- Environmental monitoring
- Water flow, water quality, Temperature, Humidity
Sensors Support (Hardware & Software)
SDI-12 Interface
| Number of Supported Sensors | Up to 2 (simultaneously), 3 pins (POWER,DATA,GND) each |
| Up to 9 if external combiner is used | |
| Supply Voltage | 12V DC (external power supply may be used as well) |
| Maximum Drawn Current | 300 mA |
| Sensors Software Support | General SDI-12 Commands Implementation (C, M) |
| Fully tested against the following models: TEROS-12 (METER), TDR-315H (ACCLIMA), Sap Flow (IMPLEXX), LI-710 (LI-COR) | |
| Advanced Features | Resistors R7,R10,R3 for controlling “power” mode |
| Jumpers J5 & J6 for controlling “measurement” mode |
4-20mA Interface
| Number of Supported Sensors | Up to 2 (simultaneously) x 2-wire or 4-wire |
| Supply Voltage | 12V DC (external power supply may be used as well) |
| Maximum Drawn Current | 300 mA |
| Sensors Software Support | Sensor-agnostic, using a 2-channel analogue current sensing circuit |
| Fully tested with Ground Water Pressure Sensor PR26Y (KEPLER)) | |
| Advanced Features | Jumpers J3 & J4 for controlling “measurement” mode |
Generic Digital Interface
| Number of Supported Sensors | 1 |
| Supply Voltage | No, the sensor should be externally powered) |
| Typical Usage | Pulse Counter |
| Advanced Features | Jumpers J7 for controlling “measurement” mode |
| Ultra-Low Power Operation Option for background pulse recording |
Advanced Features
“Power” mode
There are 2 “power” modes for both SDI-12 and 4-20mA controlled via the PCB hardware & firmware:
- “Heating” mode (default): It applies continuous 12V DC. This is required by some sensors for condensation avoidance (e.g. Oxygen Sensor SO-411 from Apogee) or special measurement procedure (e.g. Evapotranspiration Sensor which requires 30 min averaging). It is enabled through mounting R7 (1K) and not mounting R10 (0 Ohm) & R3 (1M).
- “Low-power” mode: This is a mode optimized for energy consumption. To select this mode remove R7 (1K) and mount R10 (0 Ohm) & R3 (1M). In this mode, the sensors are powered only during the micro-controller wake-up periods by enabling a special control pin from the firmware, i.e. IO37.
“Measurement” mode
In addition, with the use of Jumpers the user may control the “measurement” mode. There are 5 jumper sets:
- J5 & J6 controls the SDI-12 Sensor Port 1 and 2 respectively
- J3 & J4 controls the 4-20mA Sensor Port 1 and 2 respectively
- J7 controls the single Digital Port
The operation is controlled as follows:
- If jumpers enable the “always-on” mode (left-center pins), then the sensor data can be accessed continuously.
- If jumpers enable the “on-demand” mode (center-right pins), then the sensor data can be accessed only when the proper control pin is enabled.
“On-demand” mode is the most energy-efficient one. The control pins are:
- SDI-12 Sensors: IO42 & IO48 for Port 1 & Port 2 respectively
- 4-20mA Sensors: IO7 & IO8 for Port 1 & Port 2 respectively
- Pulse Counter Sensor: IO6
4-20mA Sensors Connection Instructions
Below you may find the proper connection instructions for 2-wire/4-wire sensors in case internal (own board) or external power supply unit is used:
-
Sensor Type: 2-wire
- Power Supply: Internal
- Sensor PWR pin connected to VIN board port
- Sensor OUT pin connected to OUT board port
- Power Supply: External
- Sensor PWR pin connected to External Supply Positive Pin (+)
- Sensor GND pin connected to External Supply Negative Pin (-)
- Sensor OUT pin connected to OUT board port
- Power Supply: Internal
-
Sensor Type: 4-wire
- Power Supply: Internal
- Sensor PWR pin connected to VIN board port
- Sensor 1st GND pin connected to GND board port
- Sensor 2nd GND pin connected to same GND board port
- Sensor OUT pin connected to OUT board port
- Power Supply: External
- Sensor PWR pin connected to External Supply Positive Pin (+)
- Sensor 1st GND pin connected to External Supply Negative Pin (-)
- Sensor 2nd GND pin connected to GND board port
- Sensor OUT pin connected to OUT board port
- Power Supply: Internal
Pulse Counter Ultra Low Power Operation Option
Many devices, like rain gauges or water flow sensors generate one or more pulses when certain liquid volume has been observed. This is different from typical SDI-12 and 4-20mA measurement scenarios, where we need to periodically wake up our IoT device (e.g. once per our hour), take a measurement and then go to deep sleep. Instead, with pulse generating sensors we need to continuously “capture” the pulses while not exhausting battery life. For this purpose we are supporting through firmware version 2.9.0 and on a special operating mode called ULP, which hosts the pulse counting measurement into an ultra-low processor drawing less than 400uA for up to 5kHz pulse frequencies.
Marking
| CE | under way |
| FCC | under way |
| RoHS | under way |
Custom designs
The existing boards are highly configurable and expandable so if the existing boards do not fit your need, get in contact with us and we will tailor a solution for you with your customizations.